By Damion Tyrell, Technology Corporate Electric
Half the lights work. Half do not. The stove elements glow weakly, the furnace fan sounds tired, and one side of the panel seems alive while the other side sits dead. This is one of the most misunderstood electrical emergencies in Markham homes and businesses, because it looks like a minor outage and behaves like something much more serious. This lesson explains what partial power loss actually is, why it can quietly damage motors and electronics while you wait, and what an emergency electrician checks first when it happens.
Technology Corporate Electric provides emergency electrician service in Toronto and the GTA for residential, commercial and industrial clients — all three sectors, served across all of Ontario from our Toronto and GTA base.
Lesson one: your building runs on two legs of power, and you can lose one
Most Ontario homes and small businesses receive a split-phase service: two 120-volt legs that combine to give 240 volts for large loads like dryers, ranges, air conditioners and shop equipment. Each leg feeds roughly half the breakers in the panel. When one leg fails — at a damaged service conductor, a failing main breaker, a corroded meter-base connection, or on the utility side of the service — exactly half the building goes dark while the other half keeps working. That pattern, half on and half off, is the signature of a lost leg, and it is different from a tripped breaker, which only kills one circuit.
In three-phase commercial and industrial buildings in Markham's industrial units, the same failure is called single-phasing: one of three phases drops out, and three-phase motors keep trying to run on what is left. That is where the real damage starts.
Lesson two: partial power is not safe power
The danger of a lost leg is not the dark half — it is the half that still runs. Motors fed with the wrong voltage draw excess current and overheat: furnace blowers, fridge and freezer compressors, well pumps, sump pumps and production motors can all cook their windings while appearing to work. In a three-phase plant, a single-phasing motor can fail in minutes under load. Electronics on the surviving leg can also see abnormal voltage as 240-volt appliances bridge the two legs and back-feed the dead side at reduced, unstable levels — which is why some lights on the "dead" half may glow dimly instead of going fully out.
The rule this teaches is simple: when half the building loses power, switch off motor-driven equipment and 240-volt appliances until the cause is found. Running them "to see if it sorts itself out" is how a service repair turns into a service repair plus a furnace, a compressor or a production motor.
Lesson three: what an emergency electrician checks, in order
A proper emergency visit for partial power loss follows a sequence. First, voltage is measured at the main breaker: if one leg reads near zero or far below 120 volts there, the fault is at or before the panel. Next, the meter base and service connections are inspected for heat damage, corrosion and loose lugs — a connection that has been heating and cooling for years often fails this way, and the Electrical Safety Authority treats deteriorated service equipment as a serious defect for good reason. If full, balanced voltage is present at the service but missing inside, the main breaker or panel bus is the suspect, and a panel upgrade in Toronto and the GTA may be the lasting repair rather than another temporary fix. If the service itself is receiving only one leg, the fault belongs to the utility, and the electrician's job is to prove that safely and document it so the utility call is precise.
What you can check yourself, safely, is limited: note which circuits are dead, look for any burning smell or heat at the panel without opening it, and turn off major motor loads. Panel covers come off only for a licensed electrician — the service conductors inside stay live even with the main breaker off.
Lesson four: the warning signs that come before a leg fails
Lost legs rarely arrive without notice. Lights that brighten and dim when a large appliance starts, intermittent outages on the same side of the building, crackling at the panel, or a main breaker that feels warm are all early evidence of a connection losing its grip. Homes in Unionville, Angus Glen and Cachet with older services, and busy commercial units along Highway 7, see the same pattern: the connection degrades slowly, then fails completely on the coldest or busiest day. Booking electrical services in Markham and across Ontario when those signs first appear is how a planned repair replaces a midnight emergency.
If half your power is out right now, treat it as the emergency it is. To reach Technology Corporate Electric, contact us— call 437-435-7053 for residential, commercial and industrial emergency service across Markham, Toronto, the GTA and all of Ontario.
By Damion Tyrell, Technology Corporate Electric
Add comment
Comments